MAIN FEATURES:
Charger & Maintainer with intelligent
function of reconditioning
Easy to use: the charger is easy to use and requires no experience
technique.
Fully microprocessor controlled
A charging Multifasei:
Renewal or manual 24h3
Automatic Renewal or a discharged battery
or Bulk Charge
Upload or absorption
or Trickle charge + Renewal
Loading & Maintenance - Automatic charging: When turned on, the charger switches
the system automatically charge, so you may be left unattended without
risk of overcharging of batteries.
Loading & Maintenance - Maintenance Automatic: When the battery is at
charge state "Full", the charger automatically switches to maintenance phase of the
battery. Monitors the battery voltage and keeps the peak
its performance
Switch Battery Type: Select lead-acid or gel.
Short circuit protection: The charger will automatically shut off when there is
a short circuit to prevent any damage.
Protection against polarity reversal: The charger can automatically shut down
when the output polarity is reversed, and withoutdamage.
Never overcharge the battery
Cables high resistance
Output Connectors corrosion resistant
Supplied with clamps and rings for terminals: Comes with a connecting cable
rapid and 2 different types of connectors, clamps and rings for the terminals. The ring terminals
are perfect for permanent connection to the battery. You can connect the cable to the
battery and keep the cable away while you are using the vehicle and, when it comes to
back to the garage, simply reconnect to the charger
PROTECTIONS FOR TEMPERATURE AND SAFETY:
The charger is equipped with 4 security guards:
INTERNAL PROTECTION FOR OVERHEATING: The charger is BS20
costruitocon an electronic circuit for overload and overheating. When the
charger is turned OFF, overheated quickly. Once the temperature decreased,
charger resumes charging normally.
PROTECTION FOR OVERLOAD: The charger employs the use of a 'Interrupter
Solid State Circuit 'which opens in a state of strong overload. This condition can
occur if you try to load highly sulfated or deeply discharged batteries. Once
the switch opens, the charger will not charge for a short time and resumed the charge
automatically with the yellow light(LED) which will be OFF, up to resume charging.
The overload may be due to an external load, remove the load condition
before groped to recharge the battery.
PROTECTION FOR THE REVERSAL: The charger has reverse polarity
of the battery and protection for short circuit. If a condition of polarity inversion
exists (the white light will become red only, while the output wires are connected to the contrary), it is
Simply unplug the charger from the wall outlet and reconnect properly as 4
described in this manual
FOR SHORT CIRCUIT PROTECTION: The battery charger is equipped with PROTECTION
Reverse polarity and short circuit. If a 'reverse polarity or an exit condition
such as to bring the charger short circuit condition exists (the red LED flashes,
while the output wires are connected to the contrary), simply unplug the charger
from the socket correctly and redo the connections as described in this manual. The
charger employs the use of a protection circuit with a solid state both in input
that the output (compared to unreliable bimetallic switches automatic), which will be activated in such a way
permanent during a catastrophic failure such as short circuit of the output cables during
charge or during stand-by, etc..
BATTERY TYPES & CAPACITY:
It is suitable for all types of lead-acid batteries. (Conventional, AGM and Gel)
12 Volt Output
Suitable for Load batteries Lead-acid or Gel:
or before connecting to the AC and connect the clamps to the battery, you must select the
mode LEAD-ACID (LEAD-ACID) or GEL with the button
Charging current: 2A
Battery capacity: the following maximum Ah capacity should be used as a
general guide: some batteries may be able to handle a higher load current.
Check with the manufacturer of the battery during charging batteries with a capacity
Charging Current 2A
Capacity of Battery: Charging 4-80AH
Battery Capacity: 4-120 in maintaining AH
ELECTRICAL COMPONENTS:
Provided by:
Power cord to the AC:
or Cable 6 feet with VDE plug
Output cable:
or 4 meters Connector Trailer
Extension Cable:
or 2 meter cable with connector pliers or Trailer +
or 2 meter cable with connector Trailer + Rings Connection
ENVIRONMENTAL:
Operating temperature: 0-40 ° C
Storage temperature: -10 - +80 ° C
Range of humidity: max. 90% RH (relative humidity)
SPECIFICATIONS:
Name Series BS20
Type Smart
Input Voltage Range 100-240
Input Frequency 50/60 Hz
Exit 2A @ 12V
Dimensions (L * W * H) 140 * 65 * 42 mm
Weight 0.45kg
Approvals CE, UL / cUL, Mzs, As
